GPIO Registers: Difference between revisions

From Vita Development Wiki
Jump to navigation Jump to search
 
(9 intermediate revisions by 2 users not shown)
Line 25: Line 25:
| 0x04
| 0x04
| 4
| 4
| Port read (1=low, 0=high?) (1 bit each port)
| Port read (0=low, 1=high) (1 bit each port)
|-
|-
| 0x08
| 0x08
Line 34: Line 34:
| 4
| 4
| Port clear (1 bit each port)
| Port clear (1 bit each port)
|-
| 0x10
| 4
| Port enable? (1 bit each port)
|-
|-
| 0x14
| 0x14
Line 45: Line 49:
| 0x1C
| 0x1C
| 4
| 4
| Gate 0 interrupts enable (1 bit each port)
| Gate 0 interrupts mask (disable) (1 bit each port)
|-
|-
| 0x20
| 0x20
| 4
| 4
| Gate 1 interrupts enable (1 bit each port)
| Gate 1 interrupts mask (disable) (1 bit each port)
|-
|-
| 0x24
| 0x24
| 4
| 4
| Gate 2 interrupts enable (1 bit each port)
| Gate 2 interrupts mask (disable) (1 bit each port)
|-
|-
| 0x2C
| 0x28
| 4
| 4
| Gate 3 interrupts enable (1 bit each port)
| Gate 3 interrupts mask (disable) (1 bit each port)
|-
|-
| 0x30
| 0x2C
| 4
| 4
| Gate 4 interrupts enable (1 bit each port)
| Gate 4 interrupts mask (disable) (1 bit each port)
|-
|-
| 0x34
| 0x34
| 4
| 4
| Port read latched? (1=low, 0=high?) (1 bit each port)
| Port read latched? (0=low, 1=high?) (1 bit each port). Used to read when port is configured as output.
|-
|-
| 0x38
| 0x38
| 4
| 4
| Interrupt status/clear (1 bit each port)
| Gate 0 interrupts status/clear (1 bit each port)
|-
|-
| 0x3C
| 0x3C
| 4
| 4
| Interrupt status/clear (1 bit each port)
| Gate 1 interrupts status/clear (1 bit each port)
|-
|-
| 0x40
| 0x40
| 4
| 4
| Interrupt status/clear (1 bit each port)
| Gate 2 interrupts status/clear (1 bit each port)
|-
|-
| 0x44
| 0x44
| 4
| 4
| Interrupt status/clear (1 bit each port)
| Gate 3 interrupts status/clear (1 bit each port)
|-
|-
| 0x48
| 0x48
| 4
| 4
| Interrupt status/clear? (1 bit each port)
| Gate 4 interrupts status/clear (1 bit each port)
|}
|}
Each of the 5 gates correspond to the 5 <code>GpioGate[i]</code> Interrupt IDs in [[Interrupts#Registered_Interrupts]].


== Interrupt mode bits ==
== Interrupt mode bits ==
Line 106: Line 112:
| Falling edge detection mode
| Falling edge detection mode
|}
|}
It seems each of the 5 Interrupt enable/clear registers correspond to the 5 <code>GpioGate[i]</code> Interrupt IDs in [[Interrupts#Registered_Interrupts]].


== GPIO Bus 0 ports ==
== GPIO Bus 0 ports ==
Line 146: Line 150:
|-
|-
| 10
| 10
| unk. Used in 0.996 [[SceEnumWakeUp]].
| unk. Used in 0.996 [[SceEnumWakeUp]] and in [[SceCamera]].
|-
|-
| 11
| 11
| unk. Used in 0.996 [[SceEnumWakeUp]].
| unk. Used in 0.996 [[SceEnumWakeUp]] and in [[SceCamera]].
|-
|-
| 12
| 12

Latest revision as of 18:25, 27 September 2022

MMIO Interfaces

Name Physical address
SceGpio0Reg 0xE20A0000
SceGpio1Reg 0xE0100000

Registers

Offset Size Description
0x00 4 Port mode (1=out, 0=in) (1 bit each port)
0x04 4 Port read (0=low, 1=high) (1 bit each port)
0x08 4 Port set (1 bit each port)
0x0C 4 Port clear (1 bit each port)
0x10 4 Port enable? (1 bit each port)
0x14 4 Interrupt mode (2 bits each port) for interrupts 0-15
0x18 4 Interrupt mode (2 bits each port) for interrupts 16-31
0x1C 4 Gate 0 interrupts mask (disable) (1 bit each port)
0x20 4 Gate 1 interrupts mask (disable) (1 bit each port)
0x24 4 Gate 2 interrupts mask (disable) (1 bit each port)
0x28 4 Gate 3 interrupts mask (disable) (1 bit each port)
0x2C 4 Gate 4 interrupts mask (disable) (1 bit each port)
0x34 4 Port read latched? (0=low, 1=high?) (1 bit each port). Used to read when port is configured as output.
0x38 4 Gate 0 interrupts status/clear (1 bit each port)
0x3C 4 Gate 1 interrupts status/clear (1 bit each port)
0x40 4 Gate 2 interrupts status/clear (1 bit each port)
0x44 4 Gate 3 interrupts status/clear (1 bit each port)
0x48 4 Gate 4 interrupts status/clear (1 bit each port)

Each of the 5 gates correspond to the 5 GpioGate[i] Interrupt IDs in Interrupts#Registered_Interrupts.

Interrupt mode bits

Value Mode
0 High level-sensing mode
1 Low level-sensing mode
2 Rising edge detection mode
3 Falling edge detection mode

GPIO Bus 0 ports

Port Description
0 OLED/LCD
1 unk
2 unk
3 Syscon related (output)
4 Syscon related (input)
5 UDCD (USB Device Controller Driver) related
6 Game Card reader LED
7 PS Button Blue LED (only blue ?? no red?)
8 unk
9 Camera
10 unk. Used in 0.996 SceEnumWakeUp and in SceCamera.
11 unk. Used in 0.996 SceEnumWakeUp and in SceCamera.
12 UDCD (USB Device Controller Driver) related
13 HDMI related (input)
14 unk
15 HDMI related (output)
16 GPO 0 (General Purpose Output - DevKit LED 0)
17 GPO 1 (General Purpose Output - DevKit LED 1)
18 GPO 2 (General Purpose Output - DevKit LED 2)
19 GPO 3 (General Purpose Output - DevKit LED 3)
20 GPO 4 (General Purpose Output - DevKit LED 4)
21 GPO 5 (General Purpose Output - DevKit LED 5)
22 GPO 6 (General Purpose Output - DevKit LED 6)
23 GPO 7 (General Purpose Output - DevKit LED 7)
24 UDCD (USB Device Controller Driver) related
25 unk
26 unk
27 Motion related
28 Motion related
29 SDIF related
30 3G Modem related
31 unk

GPIO Bus 1 ports

Port Description
7 LCD related. Backlight?

Interrupt mode used by PSVita OS

Bus Port Interrupt mode Description
0 4 3 Syscon input