Bugs
The PS Vita has bugs. Some bugs can lead to Vulnerabilities. Others lead to nothing useful (yet) but can serve as examples of what not to do.
Exploitable bugs
See Vulnerabilities.
Non-exploitable bugs
CMeP
CMeP does not check m' >= N during RSA signature verification
Discovered on 2023-02-22. Actually tested on 2023-08-21.
This is not a real bug.
Most of CMeP's RSA signature verification does not check for m' >= N.
However, you can input a value greater than N and it remains safe because it does m' % N (modulo) first through the bignum hardware.
This makes the RSA signature verification function return success when there is one legitimate signature and any number of fake signatures (m' + N * any_num).
TrustZone
SceTimerForUsleep is accessible from NS
The SceTimerForUsleep timer (Word Timer 7) is reserved for the TrustZone kernel. However, this timer's MMIO range is not blacklisted from access by ARM cores in Non-Secure state. An attacker in Non-Secure state can thus change the timer's configuration, even if it is being used from Secure state.
This timer is used for the implementation of sceKernelUsleep, which can be roughly summed up as "program the timer to send an interrupt after delay has elapsed and wait for the interrupt".
By stopping the timer while core X is executing sceKernelUsleep() in Secure state, this allows an attacker on another core in Non-Secure state to hang core X (as it waits for an interrupt that will never be delivered).
In theory, this could be used to create or enlarge a ToCToU window; in practice, this attack is useless because only the SMC 0x121 handler (inside SceDriverTzs) uses sceKernelUsleep() and it isn't vulnerable to ToCToU. This was only checked in 3.65 and may not be true in older firmwares.
For obvious reasons, interrupts are not disabled while waiting in sceKernelUsleep - thus, this vulnerability does not allow an attacker to prevent Secure state interrupts handling on a core.
Kernel
sceKernelThreadMgrModuleBoot doesn't clear q1
Discovered on 2022-08-29 by CreepNT.
At the beginning of sceKernelThreadMgrModuleBoot in SceKernelThreadMgr, a subroutine is called to initialize all VFP registers to the value 0x7FF8DEAD7F80DEAD (as double).
However, the routine forgets to set register q1, leaving it uninitialized.
This bug is not very important because it doesn't cause any malfunction and the VFP registers will be overwritten at some point when scheduling starts.
(2024-10-03) This bug in also present in SceKernelIntrMgr's IRQ exception handler, in a similar code sequence executed under certain conditions. Most likely useless.
Syscall table collision between modules
Because of the time between a slot is allocated and the time it is written to, there could be collisions. For example, assume there is one empty syscall slot left. Two modules each exporting syscalls are loaded and both of them are assigned the final free slot. One user library is loaded that imports from the first module. Then it imports from the second module. At this point, the function pointer exported by the first module is replaced with the second one.
It is unlikely this would lead to any security vulnerabilities, but it could create system instability. However, if the system has so many (let us assume more than 3000) syscalls loaded, it may be already in an unstable state.
Kernel heap pointer leak in sceKernelGetLibraryInfoByNID
Discovered on 2019-12-17 by Princess of Sleeping.
SceKernelModulemgr#sceKernelGetLibraryInfoByNID leaks a kernel heap pointer, but it is probably not useful for kernel exploitation.
SceKernelLibraryInfo.libname is a pointer to kernel memory. See SceKernelModulemgr#Types.
PoC code:
SceUID modids[0x80];
SceSize num = 0x80;
SceKernelLibraryInfo libinfo;
libinfo.size = sizeof(libinfo);
sceKernelGetModuleList(~0, modids, (int *)&num);
sceKernelGetLibraryInfoByNID(modids[num - 2], 0xCAE9ACE6, &libinfo);
sceClibPrintf("LEAKED KERNEL HEAP POINTER !!! ---> 0x%X <--- !!!\n", libinfo.libname);
Not fixed as of FW 3.600.011.
SceIofilemgr misses internal NULL pointer checks
SceIofilemgr's syscalls wrappers do various checks in usermode for the sanity of usermode arguments, but some internal functions that the syscalls call do not do proper checks.
For example, you can simply trigger a Kernel DABT by running the following code:
sceIoDevctl(NULL, 0, NULL, 0, NULL, 0);
Confirmed in FW 2.10. FWs >=3.60 have proper checks.
sceAppMgrDestroyAppByAppId triggers kernel panic
Triggering a usermode exception immediately after calling sceAppMgrDestroyAppByAppId causes ?SceKernelThreadMgr? to get confused and trigger a kernel exception.
sceKernelCreateThread in thumb mode
SceKernelThreadMgr#sceKernelCreateThreadForUser checks the memory attributes to see if the entry point is executable, but in thumb mode, the function pointer always has bit 0 as 1, so if the entry point is the last 4-bytes of a memory page, then the next check fails and returns 0x80020006.
res = sceKernelIsEqualAccessibleRangeProcBySWForDriver(pid, memory_attr, entry, 4);
sceNetRecvfromForDriver 0xC0022005 error on kernel call
This is because the internal function always sets the is_user flag in the parameter, so setting the kernel memory pointer to data in SceNetPs#sceNetRecvfromForDriver will result in an error in SceSysmem#sceKernelCopyToUserDomainForKernel or SceSysmem#sceKernelCopyToUserTextDomainForKernel.
// Offsets are for FW 3.60
// Patch by function hook
SceUID target = -1;
tai_hook_ref_t FUN_8100d5a8_ref;
int FUN_8100d5a8_patch(void *a1, void *a2, void *a3, int a4, void *a5, void *a6) {
if (target == sceKernelGetThreadIdForDriver())
*(int *)(a3 + 5 * 4) = 1; // 0:user 1:kernel 2~:kpanic
return TAI_CONTINUE(int, FUN_8100d5a8_ref, a1, a2, a3, a4, a5, a6);
}
// Patch by code injection (recommended)
int patch_netrecv_0xC0022005(void) {
/*
810067b2 c0 ef 10 00 vmov.i32 d16,#0 -> DD F8 30 C0 ldr ip, [sp, #0x30]
810067b6 19 68 ldr r1, [r3]
810067b8 a2 60 str r2, [r4, #8]
810067ba da f8 0c 30 ldr.w r3, [sl, #0xc]
810067be c4 e9 07 55 strd r5, r5, [r4,#0x1c] -> C4 E9 07 C5 strd ip, r5, [r4,#0x1c]
810067c2 a5 61 str r5, [r4, #0x18]
810067c4 e3 60 str r3, [r4, #0xc]
810067c6 61 62 str r1, [r4, #0x24]
810067c8 c4 ed 04 0b vstr.64 d16, [r4,#0x10] -> C4 E9 04 55 strd r5, r5, [r4,#0x10]
*/
SceUID module_id;
void *patch_point;
char inst[0x20];
module_id = sceKernelSearchModuleByNameForDriver("SceNetPs");
module_get_offset(0x10005, module_id, 0, 0x67b2, (uintptr_t *)&patch_point);
memcpy(inst, patch_point, 0x1E);
memcpy(&(inst[0x0]), (const char[4]){0xDD, 0xF8, 0x30, 0xC0}, 4);
memcpy(&(inst[0xC]), (const char[4]){0xC4, 0xE9, 0x07, 0xC5}, 4);
memcpy(&(inst[0x16]), (const char[4]){0xC4, 0xE9, 0x04, 0x55}, 4);
taiInjectDataForKernel(0x10005, module_id, 0, 0x67B2, inst, 0x1E);
return 0;
}
Illegal alignment check of kernel allocator
Discovered on 2021-08-30 by Princess of Sleeping.
For example, if 0x880 is passed as the alignment argument of kernel malloc, the function will not return NULL.
This affects at least SceNetPs malloc and system malloc internal/external.
Ignored sceGUIDGetNameCore error propagation
Discovered on 2022-03-10 by Princess of Sleeping.
sceGUIDGetNameCore, which is called internally by SceSysmem#sceGUIDGetNameForDriver or SceSysmem#sceGUIDGetName2ForDriver, always returns 0 even if an error occurs in the function.
void unsafe_calling_example_1(void) {
int res;
const char *name;
// Use some tricks to reach sceGUIDGetNameCore with invalid guid.
res = sceGUIDGetName((invalid_guid | 1) & ~0xC0000000, &name);
// res is always 0 even failed internally.
// And sceGUIDGetNameCore initializes name with NULL, but if the internal check fails too early, name is not initialized and is undefined.
}
void unsafe_calling_example_2(void) {
const char *name;
// Use some tricks to reach sceGUIDGetNameCore with invalid guid.
name = sceGUIDGetName2((invalid_guid | 1) & ~0xC0000000);
// res is always 0 even failed internally.
// And sceGUIDGetNameCore initializes name with NULL, but if the internal check fails too early, name is not initialized and is undefined.
// If sceGUIDGetNameCore failed internally, name value is *(uint32_t *)(unsafe_calling_example_2_current_sp - 0x10)
}
void safe_calling_example_1(void) {
int res;
const char *name = NULL; // Initialize with NULL in advance
// Use some tricks to reach sceGUIDGetNameCore with invalid guid.
res = sceGUIDGetName((invalid_guid | 1) & ~0xC0000000, &name);
// res is always 0 even failed internally.
if(NULL == name){
sceKernelPrintf("Failed %s\n", "sceGUIDGetName");
}
}
void safe_calling_example_2(void) {
int res;
const char *name;
// Add guid valid check
res = some_guid_valid_check(invalid_guid);
if (res < 0)
return; // If invalid guid it, do not call sceGUIDGetName2.
// Use some tricks to reach sceGUIDGetNameCore with invalid guid.
name = sceGUIDGetName2((invalid_guid | 1) & ~0xC0000000);
// name is always not NULL.
}
Incomplete register restore on intr handler
Discovered on 2023-03-08 by Princess of Sleeping.
Confirmed on fw 1.810.
In the example below, an interrupt occurs when rw_data is loaded. In that case the interrupt handler will handle it, but not fully restore the DACR when leaving the function, but restore it from the ThreadCB.
And what is set in ThreadCB is the kernel's default client setting of 0x55550000. So when the interrupt ends and you try to write to rx_data, a DABT occurs.
int resolve_something(void *rx_data, void *rw_data){
SceUInt32 dacr = sceKernelGetDACR();
sceKernelSetDACR(dacr | 0xFFFF0000);
int write_data = *(int *)rw_data;
// Happened intr And Setting dacr to 0x55550000 on intr_handler register restore.
*(int *)rx_data = write_data; // Trigger DABT because there is no write in RX.
sceKernelSetDACR(dacr);
return 0;
}
Add disable intr to fix these.
int resolve_something(void *rx_data, void *rw_data){
asm volatile ("cpsid aif\n");
SceUInt32 dacr = sceKernelGetDACR();
sceKernelSetDACR(dacr | 0xFFFF0000);
int write_data = *(int *)rw_data;
*(int *)rx_data = write_data;
sceKernelSetDACR(dacr);
asm volatile ("cpsie aif\n");
return 0;
}
DACR corrupte due to sceKernelIsAccessibleRangeProc
If sceKernelIsAccessibleRangeProc is specified in the pid argument, switches to the target process MMU Mapping, but does not restore DACR correctly at the time of termination processing.
Simplified code.
int sceKernelIsAccessibleRangeProc(int pid, int perm, const void *addr, int size){
if(pid != 0){
SceUInt32 dacr = sceKernelGetDACR();
set_process_mmu(pid);
sceKernelIsAccessibleRangeProc_core(perm, addr, size);
sceKernelSetDACR(dacr & 0x55555555);
}else{
// ...
}
}
Be careful if you are in Development Kit. The callback of sceKernellPrintf calls sceKernelIsAccessibleRangeProc. (SceSysmem::sceKernellPrintf -> SceDeci4pSTtyp::handler -> call sceKernelIsAccessibleRangeProc for n/s format)
Also, if you crash something when you write on RX with after DACR 0xFFFFFFFF, suspect this. This is not the only function for MMU Mapping like this.
Limited buffer size in dbginfo handler for sceKernelPrintf*
The handler properly converts dbginfo like 0:0xAAAAAAAA55555555(something_func:335):0xA5A5A5A5(file.c):Hi\n and outputs it to tty, but its buffer size is limited, so if the function name or file name is too long, the conversion will be cut off and the incorrect output will be output to tty.
Wrong range control in vnode lock/unlock
If your thread tries to lock the vnode while another thread is locking the target vnode, vp->waiter is incremented, but waiter is a 32-bit member, but the lock function Tries to increment over a range of 64-bits.
R_ARM_CALL/R_ARM_JUMP24 relocations not performed properly
Discovered on 2023-06-17 by CreepNT.
There is a bug in the SceKernelModulemgr routine that handles relocation types R_ARM_CALL (28) and R_ARM_JUMP24 (29):
//S, A and P correspond to the relocation variables detailed in the "ELF for the Arm® Architecture" document.
int displacement = (A - P) + S;
unsigned opcode = read_opcode_from_address(P);
if ((opcode & 0xF0000000) == 0x0) { //<- bug here
opcode = (opcode & 0xFEFFFFFF) | (displacement & 0x2) << 23; //write bit 1 of displacement in 'H' bit of BLX
}
opcode = (opcode & 0xFF000000) | (displacement >> 2) & 0xFFFFFF; //write displacement in imm24 (bottom 2 bits not needed due to code alignment)
write_opcode_to_address(P);
The if-gated code is supposed to handle the special case of the BLX instruction, which has an additional bit (H) of storage for the offset to target function (because ARM code is 4-byte aligned but Thumb code is 2-byte aligned). The BLX instruction should be identified because it has cond=0xF, but this code checks for cond=0x0 instead (EQ).
This bug will thus cause all relocated BLEQ instructions to turn into BEQ instructions - fortunately, this has no consequence because the instructions are equivalent.
However, and most importantly, it also results in some BLX instructions not being properly relocated (as H is not set/cleared when it should). One of three scenarios happens when a BLX is "relocated":
Hhas the correct value: everything goes fineHis set but should be clear:BLXwill skip the first instruction of the target functionHis clear but should be set:BLXwill jump to the one instruction right before the target function's start
When an improperly relocated BLX is executed, the program may end crashing (e.g. UNDEFINED abort), behave unexpectedly (function doesn't actually run, argument is corrupted, etc) or appear to work properly depending on the exact situation.
This bug exists since at least firmware 0.920 and has never been fixed. It is plausible it exists since an earlier (or even the first) revision of the OS.
sceVfsMount deadlock bug
When trying to mount a file system (vfs type 2) with sceVfsMount, if you set a regular file to SceVfsMountParam->pVfsMount2->blockdevName or SceVfsMountParam->pVfsMount2->blockdevNameNoPart instead of SceVfsMountParam->blockdevName, sceVfsMount returns 0x80010016 and the function is seems error successfully.
However, vfs_get_devfile_vnode called by sceVfsMount checks the vnode attribute (0x2000) and fails, but at this time, it returns to sceVfsMount without releasing some of the vnodes, seems causing a deadlock when the system suspends.
ScePfsMgr cannot read files larger than 0xFFFF8000 bytes
Discovered on 2023-12-12.
This was tested with sw version 3.200.
If you run the following code on a file larger than 4GiB, you can "correctly" read 0xFFFF8000-bytes (4GiB - 0x8000-bytes) without error print.
sceIoLseek(fd, 0LL, SCE_SEEK_SET);
do {
res = sceIoRead(fd, buffer, 0x8000);
if(res > 0){
// something
}
} while(res > 0);
if(res < 0){
scceClibPrintf("sceIoRead error 0x%X\n", res);
}
However, the file should be more than 4GiB, so it's clearly a bug.
Also, when run the following code, the following error log is output.
sceIoLseek(fd, 0x100000000LL /* 4GiB offset */, SCE_SEEK_SET); sceIoRead(fd, buffer, 0x8000);
And the log looks like this, with `offset=0`, so it looks like some overflow is occurring.
efile/crypt_engine_impl.c(197) _icv_gd_verify: ICV mismatch offset=0 (k=0). facade/facade.c(305) _waitfor_discard_read_packet: waitfor_crypt() r=0x80140f02. efile/crypt_engine_impl.c(306) _crypt_for_read: _issue_primitive() r=0x80140f02. facade/facade.c(410) _facade_read_pread_impl: _waitfor_discard_read_packet() r=0x80140f02. facade/facade.c(506) scePfsFacadeVfsPread: _facade_read_pread_impl() r=0x80140f02.
A icv mismatch caused by pfsmgr specification mismatch.
Discovered on 2024-11-06.
The retail packages are built with pfs_builder for file level encrypt, completeness, which has slightly different specifications for this pfs_builder than the Kernel system module.
And icv is used to ensure the completeness of game files within pfs encrypt layer, etc., and in unicv.db (RO) it has the following format:
[SCEIRODB header] [SCEIFTBL header for dir 0] [SCEIFTBL header for dir 1] [SCEIFTBL header for file 0] [hash blocks 0 for file 0] [hash blocks 1 for file 0] [SCEIFTBL header for file 1] [SCEIFTBL header for file 2] [hash blocks 0 for file 2] ...
Specifically, the mismatch occurs in the SCEIFTBL header.
// for files.db version 5 and unciv.db version 2 [SCEIFTBL main header (0x20 bytes)] [SCEIFTBL hash blocks hash (0x14 bytes)] [SCEIFTBL iv seed (0x14 bytes)]
The Kernel module's ScePfsMgr implementation calculates the hash and performs the icv matching test on the header when everything is finalized, that is, when the iv and hash blocks hash are all written.
However, the problematic pfs_builder registers this header hash in files.db before the iv seed is written.
As a result, when you try to open a particular file, you get the following error:
handler/icvdb.c(416) init_icvobj: icv mismatch. handler/pfops_impl.c(1349) pfs_impl_open: init_isec() r=0x80142002, size=0. handler/pfops.c(364) pfs_open: pfs_impl_open() r=0x80142002.
However, it's not a big deal as it only seems to cause this error with 0 byte files.
This issue appears to be fixed in the new pfs_builder.
Titles where this issue is identified:
PCSC00052 (example: data/ded.vpglsl)
Kernel Boot Loader
Out of range access in SKBL
Discovered on 2022-01-20 by Princess of Sleeping.
To decode ARZL encoded TrustZone SceSysmem, SKBL maps Compati SRAM (PA 0x1C000000) to TrustZone VA with a size of 2MiB. It then calls SKBL#sceArlzDecode with an improper argument, thus using glitches during decoding to exceed 2MiB will pass the size check and access outside the range of the device, so it can trigger a Data abort exception.
Moreover, even if SKBL#sceArlzDecode returns an error code, it will be passed to the argument of SKBL#sceArlzArmFilter without being checked, so access for up to 0x80560201-bytes will occur.
if (sceKernelCpuId() == 0) {
sceKernelMMUMapSections(*(void **)(param_1 + 0x60), 0x1061D007, 0xC, 0x1C000000, 0x200000 /* mapping size */, 0x1C000000);
res = sceArlzDecode(0x1C000000 /* dst */, 0x1000000 /* dst max size */, &ARZL_encoded_SceSysmem[4] /* src */, NULL);
size = sceArlzArmFilter(0x1C000000, res, 0);
g_Tzs_SceSysmem_start_address = 0x1C000000;
g_Tzs_SceSysmem_end_address = 0x1C000000 + size;
}
It is currently just a bug as no glitching has been tried and as a Data abort exception is not useful.
Incorrect mapping size specified to MapASLR
Discovered on 2023-07-25 by CreepNT. This bug also affects NSKBL.
Since System Software version ?, SKBL and NSKBL randomize the virtual address of objects allocated during boot that remain mapped after KBL ends.
To achieve this, the ASLR seed from KBL Param and the size of each mapping are used by the MapASLR routine.
Along with an internal bitmap to keep track of the previously allocated virtual memory pages, it finds a virtual address aligned with vsize such that enough pages to fit vsize bytes are free after it, before marking the whole range as allocated.
However, the first call to MapASLR, for SceKernelL2PageTable000, is performed with vsize=0x1000 whereas vsize=0x2000 should have been used (0x1000 of mapping + 0x1000 of extraHigh).
(Note: This may have been intentional, as SceKernelL2PageTable000 is handled specially all along (N)SKBL, but still causes a bug).
Since an invalid vsize was provided, the ASLR bitmap is not updated properly, and the SceKernelL2PageTable000 extraHigh page remains marked as free.
Depending on the ASLR seed, MapASLR may later assign its virtual address to another mapping, in which case the extraHigh page of SceKernelL2PageTable000 will not actually be unmapped.
This bug doesn't seem to cause any adverse effect, as the OS still boots and appears to work fine.
Probably present since ASLR was introduced in SKBL & NSKBL. Not fixed as of System Software 3.74.
Example with ASLR seed set to 0x000000A0 (information obtained by reading raw MemBlock objects):
SceKernelL2PageTable000 PA : 0x40201000 VA : 0x5000 psize : 0x1000 vsize : 0x2000 extraHigh : 0x1000 --- SceKernelExceptionEntry PA : 0x40200000 VA : 0x6000 psize : 0x1000 vsize : 0x2000 extraHigh : 0x1000
Notice how SceKernelL2PageTable000 is supposed to occupy 0x5000~0x6FFF, but 0x6000 is the start address of SceKernelExceptionEntry too.
Non-Secure Kernel Boot Loader (NSKBL)
Null dereference in the NSKBL kernel panic handler
(2021/06/19 by Princess of Sleeping) The kernel panic handler accesses the SceSysroot pointer, but since that pointer is set to NULL during early boot, NULL access to SceSysroot occurs.
CelesteBlue: If I understood correctly, this means that as long as NSKBL is running, a non-secure Kernel panic from any cause will end up in a DABT exception at NSKBL level.
CreepNT: The global SceSysroot pointer is initialized during sceKernelSysrootStart (soon after the MMU is brought up) and any panic after this point will not DABT.
However, if a panic happens before but the MMU is disabled, since 0 is a valid (physical) address, no DABT will occur (but since bogus "Sysroot" data will be read, system may e.g. PABT if bogus data is interpreted as a function pointer).
This only leaves a tiny window during which the MMU is enabled but sceKernelSysrootStart has not been executed where a panic will cause a DABT (but since there is basically no code in that window that can panic, a DABT should never happen because of this bug).
Present in FW 3.600.011, 3.650.011.
Out-of-bounds write in sceKernelSysrootStart
(2023/04/25 by CreepNT)
In old firmwares, during the execution of the sceKernelSysrootStart function, 0x80 bytes are allocated from the Sysroot heap then divided in 4 blocks of 0x20 bytes each. Each CPU then loads the address of its block into the TPIDRPRW register.
Later on during this same function, the sceKernelTlsKernelSet subroutine is called - however, it expects TPIDRPRW to hold a pointer to a ThreadCB (Thread object) which is much larger than 0x20, and does the following: *(uint32_t*)(TPIDRPRW + 0x74) = 0;. This results in an out-of-bounds write at offsets 0x74, 0x94, 0xB4 and 0xD4 of the Sysroot heap for CPU0, CPU1, CPU2 and CPU3 respectively.
However, this bug has no real consequence (and was probably never noticed) because the data at these offsets is:
- 0x74: inside the TPIDRPRW block, which is unused
- 0x94: inside a 0x28 bytes allocation which has not been written to yet
- 0xB4: inside heap padding (all allocations are rounded up to 32/64B boundary)
- 0xD4: offset 0x14 inside the
SceKblParamstructure, which is unused
Exists since at least System Software version 0.920.050. Fixed in System Software 0.990 - due to a rework of the kernel TLS system, sceKernelTlsKernelSet was removed; thus the invalid call is no longer performed.
Incorrect mapping size specified to MapASLR
Shell
Unvalidated IPMI arguments lead to DoS
(2023/05/31 by CreepNT, reported by M Ibrahim) At least one IPMI server (SceDownload) does not validate the amount of IPMI::DataInfo (input) or IPMI::BufferInfo (output) arguments received before using them. This leads to garbage being used as pointers and dereferenced, in turn crashing the SceShell process due to a Data Abort Exception.
It might be possible to use this as a vector for a data-only attack on Shell.
Present in firmware 3.60.
SCE Library
SceLibJson's infinite loop on Parse
Even if you try to parse json of small size, an infinite loop will occur inside Parse for certain json.
Patched in firmware 3.55.