Search results

...accessory port found only on the original PS Vita models is a custom port USB interface. The port must be activated in software and so far, there does no ...y port working and able to mount a USB drive via VitaShell by hacking Mini-USB cables].

...ses a proprietary multi-connector on the OLED (PCH-1XXX) units and a micro-USB on the LCD (PCH-2XXX) units. ...adaptor, there exists a way to use the port in host mode probably through USB OTG or something similar.

...PS Vita is powered off and connected to a PC, this chip is likely what the USB sees?? ...duct/TS3USB31 TS3USB31RSER] USB switch is connected to Cookie and Kermit's USB interfaces.

...on_script|System Configuration script]] when the console starts because of USB enumeration. ...ly shuts off the console after it's plugged into anything that triggers an USB enumeration. The module may also present the <code>DevIcon.fil</code> file

Selects USB port to use and selects host or client mode. Gets server mode (host or client) of the specified USB port.

* Activate USB serial device * Setup USB serial device

/** USB Status * Get state of a specific USB driver

| USB | USB Device Controller. Connecting to host PC or USB OTG.

| UDCD (USB Device Controller Driver) related | UDCD (USB Device Controller Driver) related

* Stops USB Dev Serial device * Initialize USB Dev Serial device

...gram. Communication Processor seems to manage input/output from sdio (mini-USB) at regular intervals.

# mini-USB connector from the CP. ...ight: USB hub. SMSC USB2512B model. Above that: crystal for USB. Allows CP USB port to export an interface to CP processor as well as Kermit.

* USB Mass Storage | uma || 3 || usb mass || USB mass storage device

These name and version show up in the USB descriptor. Sets the filesystem image to use as USB storage. This is limited to the CMA installer ISO and a FAT image at <code>

...whisperer. Remove the jumper to drive the eMMC from the adapter and enable USB data (see notes above for when you can do this). # Make sure the USB port is soldered properly. Check +5V to C16, GND, and D+/D- to USB2244 pins

* [[Cookie]]: USB Charge Management IC

...PS Vita by USB to the host PC and launch the "EMPR" mode on the PS Vita, "USB mode" on the PSP/PSPgo. Finally, on the host PC you select which videos you

It has an extra LED and mini USB/HDMI in the hardware.

=== USB === | D+ 3G || AD24 || 3G modem USB D+ (host EHCI)

USB Hub. Directly connected to the data lines of the mini-USB type B port and to the [[Communication Processor#SMSC USB3315|USB3315]]. Da Hi-Speed USB Transceiver with 1.8V-3.3V UPLI interface. Connected to the [[Communication

...PervasiveForDriver_13CC07C9 <br> <br> 0x1 - USB Host Controller <br> 0x2 - USB Device Controller <br> 0x8 - ???? ...PervasiveForDriver_AD1E81EB <br> <br> 0x1 - USB Host Controller <br> 0x2 - USB Device Controller <br> 0x8 - ????

...0x3D2, 0xC001C0 USB charge on SLIM, 0xC503D2 USB charge on SLIM, 0xC501CA USB data to PC) | USB Enum Wake Up Debug Menu.

...[SceDS3]] module calls this function to register the DualShock3/DualShock4 USB/Bluetooth driver. Only one virtual controller driver can be registered at a

...onnected, you will get disconnected from TM server until you reconnect the USB cable. You may still experience timeouts when running the psp2ctrl info com

| USB Control. | USB Slave Bus

echo Not wakeup due to USB enum! echo No USB enum wakeup!

...S-1001 Wlan/Bt module USB or PS Vita 3G modem USB. This also affects PS TV USB host and maybe also PS TV ethernet. ...callbacks (maybe constructor and destructor or callback and args) for mini-USB OTG on PS Vita Slim.

First 0x40 bytes are the USB Driver Device Id. It is the serial number reported via the MTP protocol (32

// cond: 4: WlanBt related, 0x20: WlanBt related, 0x8000: USB charge

/** USB WLAN module. Gamesharing */

Sets active bus for UDC (USB Device Controller).